- [Instructor] Here I'm going to talk about points,
and these points are going to be external to sketches.
So, for the exercise file, we've shown you where to download
that from, or, if you have access to the CATIA help
documents, simply select on the feature that you want,
select F1, and what'll happen is it'll pop up
the help documentation, and within that documentation,
you'll have a Points3D1.CATPart, so you can download it
from there as well and go to work.
So, for points, there are several ways in which
you can create points.
You'll notice that you have a little pulldown at the top.
Hit by coordinates on curve, plane,
surface, sphere, and so on.
So, for the first one, by coordinates, you'll notice
that I can just simply enter in XYZ coordinate locations.
So, at this point, this is based off of the origin
and the default axis, so if I simply select OK,
you'll notice, let me zoom in a little bit.
In my XYZ coordinates, my point appears.
I'm going to simply select OK to create that point.
Now, I'm going to create another point, based off of
those exact same coordinates, but this time,
instead of the default reference point being the origin,
I'm going to use the previous point that I created
as my default reference.
So, as you can see, I can quickly change
what I'm measuring to or from.
This is very handy, because a lot of times, if I'm working
in aircraft coordinate or automobile coordinate systems,
I'm not always going to be at the front end of the aircraft
or the vehicle, I'm oftentimes working at the rear,
and in some cases, that may be 100, 200,
300, 400 inches away, depending on the size of the aircraft
or the vehicle, it could be even further away,
depending, again, on what I'm working on.
If this is a building, this may be 10, 20, 30,
50 stories tall, so you want to use a local reference.
So you can set that local reference up with a coordinate
and then use that coordinate point to help define
the base location for all of your incoming geometry.
Next, we have what's called on curve.
And I'm going to come in, I'm going to select this curve first.
And what it does, by default...
My bad, I'm using the original reference,
I'm just going to clear this out.
I'm going to right mouse click, say clear selection.
By default, it's going to pick one of the end points
off of that curve, and you'll see a little green square,
and that little green spare is indicating which end
it's coming from, and then you have a red arrow,
indicating the direction that it's going to be measured in.
Here, I can just simply click to get the location,
and you'll see a little blue square indicating where
the point is going to end up.
I can say distance on curve, distance along the direction,
ratio on curve length, and I can come in here,
enter in a value.
I can say say middle point, it'll put it right
in the middle of the curve.
You'll notice that it changed the difference to reference.
In order to get a middle point, it has to use a ratio
of the length, from zero to 1.5 being right in the middle.
I can say nearest extremity, and it'll go to one end point,
or if I want to, I can just say zero here
and go to the other end point.
You'll see now, it's at that end point.
You'll also notice that I have a couple of options here
for geodesic and euclidean, and depending upon
what you're designing, a lot of times, oftentimes,
you need the specific length of something or a specific
distance away from something, so one of 'em will give you
the actual length along the curve, so in this case,
it'll say geodesic, and I'll just say .3,
enter, and it takes me all the way out to this point.
Now, you'll notice, if I go in and do the same thing,
try to do the same thing, and this time,
I'm going to say euclidean, it's going to say
there's no solution for this operation.
And the reason is is because with a euclidean,
I have to measure the true distance from the end point,
based off of as the crow flies, not along the curve.
And because of that, the only option is
what's called distance on curve.
So if I switch this to euclidean, you may get a little
message that pops up and says hey, I'm changing this on you,
and it's describing, yes, it's an error,
but it's not really an error.
So now I can type in that length, whatever value I type in.
150.
And it places it there.
Now, this time, I'm going to create another point.
I'm going to leave it at geodesic, distance on curve,
same manner, everything's exactly the same as the euclidean
except for the type of offset.
I'm going to enter in 150.
And you'll notice that 150 is up, 'cause this time,
it's measuring away on the length of the curve,
not measuring away a distance from that point.
So, two very different results.
So just be careful on how you're inputting those point
with the distances along the curve.
Once again, I've spoken about this previously.
I can say default extremity if I want to measure away from
a reference point, rather than one of the end points,
so I can come in and specify that reference point.
We'll go back in a point.
We have on curve, on plane, I specify the plane,
and you'll notice it sets up a reference, horizontal
and vertical access on that plane, just a temporary,
saying you're measuring off of this origin.
Again, I can specify a different origin.
And based off of that HV, I can just either pick a point
or enter in those coordinates.
You have on surface, and we'll go over here
to this purple surface.
Simply pick the surface you want to go to, and you'll notice
that, by default, the reference is the middle.
This is just dynamic positioning on that surface.
Right now, it sets a course.
If I go to find, it'll just attenuate the actual value
to a finer, I guess, distant measurement, that's all,
nothing fancy.
I can place that point, select OK.
And, once again, I'll go in, put a point on that surface,
and this time, instead of using the reference as the middle,
I can select that point, now measuring away
from that point, specifically.
We have circle, sphere or ellipse center.
So here, you'll notice that I picked this spherical surface
and it wants to put it in to the center of that sphere.
I can also pick a circular edge, and it'll go to that edge.
Tangent on curve.
Now, for this, I'm going to pick this curve,
and it's going to ask me for a direction.
What direction do I want to go in?
And I'm just going to pick the XY plane.
Then you'll notice, at this location,
I have a tangent curve that can be drawn,
based off of this vector.
So, wherever it's tangent on that curve,
that's where it falls.
This is a very handy features.
Oftentimes, you want to do a parting line or reflect line
to a tooling direction, you need to know where that's
going to fall or start, so this is good for that.
And the last one is what's called between.
And with between points, you specify two points,
point one, point two.
If I just simply hit preview, let me give it a ratio
distance between the two, preview, you'll notice that
this is at .4 between these two points,
directly between those two.
I can also give it a support.
In this case, I'll say this curve.
So, in between this point and this point, that point
is .4 out, and it's projected down onto that curve.
So, use points.
They're very stable, very handy elements, easy to get
references set up pretty much anywhere on the model.
Good modeling practice is, again, to use a point
in a location that's relevant to the model that you're
designing within the context or within the realm
or the world that the part sits in.
So if you're designing, let's say, a bumper at the back end
of the car, you'll use a tooling hole or specific location
to model things up against, same thing with an aircraft
or anything larger, buildings and so on.